Power transmission system with taut belt connecting two pulleys
The block represents a pair of pulleys connected with a flexible flat band or V-shaped belt. The model accounts for friction between the flexible belt and the pulley periphery. If the friction force is not sufficient to drive the load, the model allows slip. The relationship between the tensions in the tight and loose branches conforms to the Euler equation. The model accounts for centrifugal loading in the flexible belt, pulley inertia, and bearing friction. The schematic shows the belt drive.
In this schematic, a) represents an open belt configuration, and b) represents a crossed belt configuration. In the open belt configuration, both pulleys tend to rotate in the same direction, and the larger pulley tends to have a larger belt wrap angle. In the crossed belt configuration, the pulleys tend to rotate in opposite directions, and both pulleys have the same wrap angle.
For open belt configurations, the following equations compute the wrap angles:
θA is the wrap angle of pulley A.
θB is the wrap angle of pulley B.
RA is the effective radius of pulley A.
RB is the effective radius of pulley B.
C is the distance between the centers of pulley A and pulley B.
The wrap angles for crossed belt configurations use this equation:
This schematic shows the open band configuration.
The spring and damper blocks account for compliance in the belt.
For more information about the dynamic equations used for the belt/pulley contact, see the Belt Pulley block reference page.
Connections A and B are the conserving mechanical rotational ports associated with the shafts of pulleys A and B, respectively.
The pulleys do not translate.
The friction coefficient and friction velocity threshold between the belt and each of the pulleys is the same.
Select the type of belt drive that you want to model.
Open belt — (Default)
The schematic in this page shows the two drive types.
Type of flexible element modeled.
Flat band — (Default)
V-belt— Exposes the V-belt sheave angle and Number of V-belts parameters.
Sheave angle of the V-belt. Default is 30 deg.
The V-belt sheave angle parameter is visible only when the Belt type parameter is V-belt.
Number of parallel V-belts. Default is 1.
Non-integer values are rounded to the nearest integer. Increasing the number of belts increases the friction force, effective mass per unit length, and maximum allowable tension.
The Number of V-belts parameter is visible only when the Belt type parameter is V-belt.
Linear density of each belt. Default is 0.6 kg/m.
The model uses this to calculate the centrifugal loading.
The effective stiffness of the belt. Default is 1e+4 N/m.
Effective damping of the belt. Default is 1000 N/(m/s).
Tension in the belt when the belt and pulleys are at rest. A positive value indicates that both pulley branches are initially in tension. A negative value indicates that the branches are initially slack. The default value is 100 N.
Specifies whether the block throws an assertion when the belt tension is too large.
No maximum tension — (Default)
Specify maximum tension— Throws an assertion when the belt tension is too high. Exposes the Belt maximum tension parameter.
Maximum allowable tension for each belt. Default is 1e+5 N.
When the tension on either end of the belt meets or exceeds this value, the simulation ends with an error.
The Belt maximum tension parameter is visible only when the Maximum tension parameter is Specify maximum tension.
Select the Pulley A tab to specify the characteristics of pulley attached to port A, and the Pulley B tab to specify the characteristics of pulley attached to port B.
Radius of the pulley. Default is 0.15m for pulley A and 0.3 m for pulley B.
Viscous friction associated with the bearings that hold the axis of the pulley. Default is 0 N*m/(rad/s) for pulley A and 0.001 N*m/(rad/s) for pulley B.
Specifies whether the block models rotational inertia of the pulley.
No inertia — (Default)
Specify inertia and initial velocity— Models rotational inertia. Exposes the Pulley inertia and Pulley initial velocity parameters.
Rotational inertia of the pulley. Default is 0.01 kg*m^2 for pulley A, and 0.03 kg*m^2 for pulley B.
The Pulley inertia parameter is visible only when the Inertia parameter is Specify inertia and initial velocity.
Initial rotational velocity of the pulley. Default is 0 rad/s.
The Pulley initial velocity parameter is visible only when the Inertia parameter is Specify inertia and initial velocity.
Select the Contact tab to specify contact characteristics.
Coulomb friction coefficient between the belt and the pulley surface. Default is 0.5.
Specifies whether the block calculates the wrap angle of the belt on the pulleys using the pulley radii, center separation, and drive type or if the wrap angles are specified directly.
Specify pulley center separation — (Default) The block calculates the wrap angle of the belt on the pulleys using the pulley radii, center separation, and drive type.
Exposes the Pulley center separation parameter.
Specify wrap angles — Uses the wrap angles that you specify.
Exposes the Pulley A wrap angle and Pulley B wrap angle parameters.
Distance between the centers of the pulleys. Default is 0.5 m.
The Pulley center separation parameter is visible only when the Wrap calculations parameter is Specify pulley center separation.
Angle of contact between the belt and pulley attached to port A. Default is 145 deg.
The Pulley A wrap angle parameter is visible only when the Wrap calculations parameter is Specify wrap angles.
Angle of contact between the belt and pulley attached to port B. Default is 215 deg.
The Pulley B wrap angle parameter is visible only when the Wrap calculations parameter is Specify wrap angles.
Relative velocity required for peak kinetic friction in the contact. The friction velocity threshold improves the numerical stability of the simulation by ensuring that the force is continuous when the direction of the velocity changes. Default is 0.001 m/s.
Conserving rotational port associated with the shaft of pulley A
Conserving rotational port associated with the shaft of pulley B